todo:start
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
todo:start [2015/05/11 04:03] vk6nk [IC-706MKIIG] |
todo:start [2015/07/12 05:38] vk6nk [20m roof antenna] |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| [[:todo:antennas:20mroofvertical|Antenna Page]] | [[:todo:antennas:20mroofvertical|Antenna Page]] | ||
| - | * Replace top sections with 2.7m stainless steel whip | + | * <del>Replace top sections with 2.7m stainless steel whip</del> |
| - | * Double hose-clamp at top, single at bottom. | + | * <del>Double hose-clamp at top, single at bottom.</del> |
| - | * Bonding wire | + | * <del>Bonding wire</del> |
| - | * Tune | + | * <del>Tune</del> |
| + | * <del>Weather proof feed point</del> | ||
| * Replace feeder with RG213 | * Replace feeder with RG213 | ||
| * <del>Radio connection</del> | * <del>Radio connection</del> | ||
| - | * Antenna connection | + | * <del>Antenna connection</del> |
| * Install ATU | * Install ATU | ||
| - | * LDG Z100Plus | + | * LDG AT7000 |
| ===== 10m roof antenna ===== | ===== 10m roof antenna ===== | ||
| Line 41: | Line 43: | ||
| * Rig [[:todo:antennas:portable20mvertical|portable 20m vertical]] using collapsible pole | * Rig [[:todo:antennas:portable20mvertical|portable 20m vertical]] using collapsible pole | ||
| + | * 9m squid-pole | ||
| + | * 5m squid-pole | ||
| + | * 5.6m tent pole | ||
| * Test [[:todo:antennas:qrptuner|tuner]] with long wire | * Test [[:todo:antennas:qrptuner|tuner]] with long wire | ||
| * AGC board | * AGC board | ||
| Line 50: | Line 55: | ||
| * Make double-adaptor anderson plug | * Make double-adaptor anderson plug | ||
| * <del>Earth lead</del> | * <del>Earth lead</del> | ||
| + | * <del>Frequency alignment</del> | ||
| + | * External speaker | ||
| + | * Compare RX sensitivity to IC-706 using R2000 | ||
| + | * Audio connections for computer | ||
| + | * Possibly use Dad's RigBlaster | ||
| * Install relay-replacement mod | * Install relay-replacement mod | ||
| * Setup panadaptor port and connect RTL-SDR receiver | * Setup panadaptor port and connect RTL-SDR receiver | ||
| * <del>Enable IF output through jumper settings</del> | * <del>Enable IF output through jumper settings</del> | ||
| * Measure output voltage of IF | * Measure output voltage of IF | ||
| + | * Attempted with oscilloscope - no signal recorded | ||
| + | * Try again with R2000 as signal source | ||
| * Build attenuator to match signal down to RTL level | * Build attenuator to match signal down to RTL level | ||
| + | |||
| + | ===== Car Radios ===== | ||
| + | |||
| + | * Install fuse block | ||
| + | * Mount speaker | ||
| + | * Fix speaker connections | ||
| + | * Hands-free | ||
| + | * Microphone | ||
| + | * Pre-amp | ||
| + | * PTT switch | ||
| ===== Study ===== | ===== Study ===== | ||
| * Clean up! | * Clean up! | ||
| - | * IKEA shelves next to desk for PC, PSU, Server, etc | + | * <del>IKEA shelves next to desk for PC, PSU, Server, etc</del> |
| * Construct monitor stand and install radios | * Construct monitor stand and install radios | ||
| * Bookshelf | * Bookshelf | ||
| * Echo dampening (framed posters/shelves?) | * Echo dampening (framed posters/shelves?) | ||
| * Install new network ports | * Install new network ports | ||
| - | * Install new power points | + | * [[todo:OfficePower|Power Distribution]] |
| - | * Improve DC distribution | + | * Install new power points |
| + | * Improve DC distribution | ||
| * Relocate printers (stacking shelves?) | * Relocate printers (stacking shelves?) | ||
| * Build speakers & amp | * Build speakers & amp | ||
todo/start.txt · Last modified: 2016/10/24 07:09 by vk6nk
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
