todo:start
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
todo:start [2015/04/28 04:13] vk6nk [20m roof antenna] |
todo:start [2015/07/12 05:38] vk6nk [20m roof antenna] |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| [[:todo:antennas:20mroofvertical|Antenna Page]] | [[:todo:antennas:20mroofvertical|Antenna Page]] | ||
| - | * Replace pole | + | * <del>Replace top sections with 2.7m stainless steel whip</del> |
| - | * Replace loading coil | + | * <del>Double hose-clamp at top, single at bottom.</del> |
| - | * Possibly use spring from Bunnings. Needs good electrical connection (self-tapper screw, pipe sleeve/insert) | + | * <del>Bonding wire</del> |
| - | * Needs weather proofing | + | * <del>Tune</del> |
| - | * Replace earth coil | + | * <del>Weather proof feed point</del> |
| - | * Possibly use spring from Bunnings. | + | |
| - | * Needs weather proofing | + | |
| - | * Lengthen wire | + | |
| - | * Take total length of antenna to 3.9m | + | |
| * Replace feeder with RG213 | * Replace feeder with RG213 | ||
| + | * <del>Radio connection</del> | ||
| + | * <del>Antenna connection</del> | ||
| * Install ATU | * Install ATU | ||
| - | * LDG Z100Plus | + | * LDG AT7000 |
| - | * Install capacity hat | + | |
| - | * Look at potentially replacing with a 5m fibreglass squid pole | + | |
| ===== 10m roof antenna ===== | ===== 10m roof antenna ===== | ||
| Line 24: | Line 20: | ||
| [[:todo:antennas:10mroofvertical|Antenna Page]] | [[:todo:antennas:10mroofvertical|Antenna Page]] | ||
| + | * Install balun | ||
| * Install earth coil | * Install earth coil | ||
| * Compare with 20m + ATU | * Compare with 20m + ATU | ||
| * Possibly replace with stainless steel whip | * Possibly replace with stainless steel whip | ||
| + | |||
| + | ===== Misc antenna work ===== | ||
| + | |||
| + | * Connect new GPS antenna | ||
| + | * Re-locate microwave antenna | ||
| + | * Move weather station on TV antenna pole | ||
| + | * Move temp sensor to bottom of pole | ||
| + | * Re-use second TV antenna pole to brace 20m antenna | ||
| ===== IC-706MKIIG ===== | ===== IC-706MKIIG ===== | ||
| Line 33: | Line 38: | ||
| * <del>Invert PPT from RTS</del> | * <del>Invert PPT from RTS</del> | ||
| * DC blocking cap on PC Mic port | * DC blocking cap on PC Mic port | ||
| + | * Mount for quick removal / reconnection | ||
| ===== X1M ===== | ===== X1M ===== | ||
| * Rig [[:todo:antennas:portable20mvertical|portable 20m vertical]] using collapsible pole | * Rig [[:todo:antennas:portable20mvertical|portable 20m vertical]] using collapsible pole | ||
| + | * 9m squid-pole | ||
| + | * 5m squid-pole | ||
| + | * 5.6m tent pole | ||
| * Test [[:todo:antennas:qrptuner|tuner]] with long wire | * Test [[:todo:antennas:qrptuner|tuner]] with long wire | ||
| * AGC board | * AGC board | ||
| Line 42: | Line 51: | ||
| ===== IC-720A ===== | ===== IC-720A ===== | ||
| - | * Connect memory backup supply to constant 12V study supply | + | * <del>Connect memory backup supply to constant 12V study supply</del> |
| * Connect main 12V supply to high-current PSU | * Connect main 12V supply to high-current PSU | ||
| * Make double-adaptor anderson plug | * Make double-adaptor anderson plug | ||
| + | * <del>Earth lead</del> | ||
| + | * <del>Frequency alignment</del> | ||
| + | * External speaker | ||
| + | * Compare RX sensitivity to IC-706 using R2000 | ||
| + | * Audio connections for computer | ||
| + | * Possibly use Dad's RigBlaster | ||
| * Install relay-replacement mod | * Install relay-replacement mod | ||
| * Setup panadaptor port and connect RTL-SDR receiver | * Setup panadaptor port and connect RTL-SDR receiver | ||
| * <del>Enable IF output through jumper settings</del> | * <del>Enable IF output through jumper settings</del> | ||
| * Measure output voltage of IF | * Measure output voltage of IF | ||
| + | * Attempted with oscilloscope - no signal recorded | ||
| + | * Try again with R2000 as signal source | ||
| * Build attenuator to match signal down to RTL level | * Build attenuator to match signal down to RTL level | ||
| + | |||
| + | ===== Car Radios ===== | ||
| + | |||
| + | * Install fuse block | ||
| + | * Mount speaker | ||
| + | * Fix speaker connections | ||
| + | * Hands-free | ||
| + | * Microphone | ||
| + | * Pre-amp | ||
| + | * PTT switch | ||
| ===== Study ===== | ===== Study ===== | ||
| * Clean up! | * Clean up! | ||
| - | * IKEA shelves next to desk for PC, PSU, Server, etc | + | * <del>IKEA shelves next to desk for PC, PSU, Server, etc</del> |
| * Construct monitor stand and install radios | * Construct monitor stand and install radios | ||
| * Bookshelf | * Bookshelf | ||
| * Echo dampening (framed posters/shelves?) | * Echo dampening (framed posters/shelves?) | ||
| * Install new network ports | * Install new network ports | ||
| - | * Install new power points | + | * [[todo:OfficePower|Power Distribution]] |
| - | * Improve DC distribution | + | * Install new power points |
| + | * Improve DC distribution | ||
| * Relocate printers (stacking shelves?) | * Relocate printers (stacking shelves?) | ||
| * Build speakers & amp | * Build speakers & amp | ||
todo/start.txt · Last modified: 2016/10/24 07:09 by vk6nk
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
